🕑 Reading time: 1 minute
Contents:
To Determine Particle Size Distribution of Soil by Sieving
The soil is sieved through a set of sieves. The material retained on different sieves is determined. The percentage of material retained on any sieve is given by Where = mass of soil retained on sieve ‘n’ M= total mass of the sample. The cumulative percentage of the material retainedCn = P1 + P2 + P3 + . . . . . . . . . +Pn
Where P1, P2 etc are the percentages retained on sieve 1, 2 etc which are coarser than sieve ‘n’. The percentage finer than the sieve ‘n’Equipment for Particle Size Distribution
- Set of fine sieves, 2mm, 1mm, 600 micron, 425, 212, 150, and 75 micron.
- Set of coarse sieves, 100mm, 80mm, 40mm, 10mm, and 4.75mm.
- Weighing balance with accuracy of 0.1% of the mass of the sample.
- Oven
- Mechanical shaker
- Trays
- Mortar with a rubber covered pestle.
- Brushes
- Riffler
Part-I: Coarse Sieve Analysis of Soil
Procedure: 1. Take the required quantity of the sample. Sieve it through a 4.75mm Is sieve. Take the soil fraction retained on 4.75mm IS sieve for the coarse sieve analysis (Part-I) and that passing through the sieve for the fine sieve analysis (Part-II). 2. Sieve the sample through the set of coarse sieves by hand. While sieving through each sieve, the sieve should be agitated such that the sample rolls in irregular motion over the sieve, the material retained on the sieve may be rubbed with the rubber pestle in the mortar, if necessary. Care shall be taken so as not to break the individual particles. The quantity of the material taken for sieving on each sieve shall be such that the maximum mass of material retained on each sieve does not exceed the specified value. 3. Determine the mass of the material retained on each sieve. 4. Calculate the percentage of soil retained on each sieve on the basis of the total mass of the sample, taken in step (1). 5. Determine the percentage passing through each sieve.Part-II: Fine Sieve Analysis of Soil
6. Take the portion of the soil passing 4.75 mm IS sieve. Oven dry it at 105 to 1100C. Weigh it to 0.1% of the total mass. 7. Sieve the soil trough the nest of fine sieves, the sieves should be agitated so that the sample rolls in irregular motion over the sieves. However, no particles should be pushed through the sieve. 8. Take the material retained on various sieves in a mortar. Rub it with rubble pestle, but do not try to break individual particles. 9. Reserve the material through the nest of sieves. A minimum of 10min of shaking is required if a mechanical shaker is used. 10. Collect the soil fraction retained on each sieve in a separate container. Take the mass. 11. Determine the percentage retained, cumulative percentage retained, and the percentage finer, based on the total mass taken in step (1).Data Sheet for Sieve Analysis
Total mass of dry soil=______g Mass of soil retained on 4.75mm sieve = ________g Mass of soil passing 4.75mm sieve = _______gObservations | Calculations | ||||
IS Sieve | Size of opening | Mass of soil retained | Percentage retained | Cumulative % retained | % finer |
Coarse Fraction (Part-I) | |||||
100 m | 100 mm | ||||
80 mm | 80 mm | ||||
40 mm | 40 mm | ||||
20 mm | 20 mm | ||||
10 mm | 10 mm | ||||
4.75 mm | 4.75 mm | ||||
Fine Fraction (Part-II) | |||||
2 mm | 2 mm | ||||
1 mm | 1 mm | ||||
600 | 0.600 mm | ||||
425 |
0.425 mm | ||||
300 |
0.300 mm | ||||
212 |
0.212 mm | ||||
150 |
0.150 mm | ||||
75 |
0.075 mm | ||||
- |
Fig: Particle size distribution on semi log graph
Fig: Grading of soils
[Note: If the fraction contains an appreciable amount of clay particles, the wet sieve analysis is required. Alternatively following method may be used. Before conducting step (7), add the water containing sodium hexametaphosphate at the rate of 2g per litre of water to the soil fraction. Stir the mix thoroughly and leave for soaking. Wash the soaked specimen on a 75